Software Testing Lab 6th Semester Diploma in Computer Science & Engineering
Information Storage and Management Diploma in Computer Science & Engineering Sixth Semester
Govt. of Karnataka, Department of Technical Education Diploma in Computer Science & Engineering Sixth Semester Subject: Information Storage and Management Max. Marks: 100 Max. Time: 3 Hours Model Question Paper Note: 1. Section –I is compulsory. 2. Answer any TWO questions from each remaining Sections. |
Network Security and Management Model Question Paper Sixth Semester Diploma in Computer Science
Network Security and Management Model Question Paper Sixth Semester Diploma in Computer Science Govt. of Karnataka, Department of Technical Education Diploma in Computer Science & Engineering Sixth Semester Subject: Network Security and Management Max. Marks: 100 Max. Time: 3 Hours Model Question Paper Note: 1. Section –I is compulsory. 1. Answer any TWO questions from each remaining Sections. |
Network Security & Management Sixth Semester Diploma in Computer Science & Engineering
SN | Content | Hours | Marks |
1 | Introduction | 2 | 5 |
2 | Organizational Policy and Security | 4 | 10 |
3 | Security infrastructure | 2 | 5 |
4 | Cryptography | 12 | 30 |
5 | Hardware & Software Security | 6 | 15 |
6 | Intrusion Detection System | 6 | 15 |
7 | Network Security | 12 | 30 |
8 | Wireless Security | 6 | 15 |
9 | Security & law | 2 | 5 |
10 | Internet governance and electronics mail policy | 4 | 10 |
Seminars, Guest Lectures, Industry Visit and other Innovations | 5 | ||
Tests | 3 | ||
Total | 64 | 140+5 Objectives |
6th sem Mobile Computing Diploma in Computer Science
6th sem Software Testing Model Question Paper computer science
6th sem Software Testing Model Question Paper computer science Courtly: Dte board Govt. of Karnataka, Department of Technical Education Diploma in Computer Science & Engineering Sixth Semester Subject: Software Testing |
Diploma in Computer Science & Engineering Sixth Semester Software Testing
6TH SEMESTER NON-CONVENTIONAL ENERGY ENGINEERING DIPLOMA IN MECHANICAL ENGINEER
TOPIC ANALYSIS:
Sl.No | Major Topics | Hours | Weightage of Marks |
SECTION-I | |||
1 | Introduction to Non Conventional Energy Sources | 01 | 05 |
2 | Solar Energy Engineering | 12 | 30 |
3 | Wind Energy Engineering | 08 | 15 |
SECTION-II | |||
4 | Ocean Energy Engineering | 07 | 20 |
5 | Geothermal Energy Engineering | 06 | 15 |
6 | Bio based Energy Engineering | 06 | 15 |
SECTION-III | |||
7 | Direct Energy Conversion Systems | 08 | 25 |
8 | Energy Storage | 06 | 20 |
9 | Environmental concerns and Industry Innovations | 06 | - |
10 | Test and Revision | 04 | - |
Total | 64 | 145 |
Non Conventional Energy Engineering MODEL QUESTION PAPER 6TH SEMESTER DIPLOMA IN MECHANICAL ENGINEERING KARNATAKA
MODEL QUESTION PAPER SUBJECT : Non Conventional Energy Engineering SUBJECT CODE :_______ TIME : THREE HOURS TOTAL MARKS : 100 ________________________________________________________________________ Note : 1) Section – I is compulsory . 2) Answer any TWO FULL QUESTIONS FROM SECTION – II, III & IV SECTION – I Q – I ) a) State a) Fill in the blanks with appropriate words 1X5= 5 i) Coal is an example of __________ source of energy ii) Fuel cell is used for ________. iii) Lead Acid battery is used for ______________ . iv) __________ is used for power generation where high velocity winds are available. v) Digester process is used in ___________ energy production. |
METAL CASTING SCIENCE AND ENGINEERING Diploma Mechanical engineering 6th semester DTE
TOPIC ANALYSIS
Sl.No | Major Topics | Hours Allotted | Weightage of Marks |
SECTION-I | |||
1 | Introduction to Metal Casting | 04 | 10 |
2 | Gating and Risering | 10 | 25 |
3 | Melting and Pouring Practice | 07 | 20 |
SECTION-II | |||
4 | Cleaning and Inspection of Castings | 08 | 20 |
5 | Casting Defects and Quality control in Foundries | 05 | 15 |
6 | Mechanisation, Computerisation and Pollution Control of Foundries | 06 | 20 |
SECTION-III | |||
7 | Application of CAD/CAM in Foundries | 08 | 20 |
8 | Casting Simulation and Optimization | 06 | 15 |
9 | Environmental concerns and Industry innovations | 06 | - |
10 | Tests and Revisions | 04 | - |
Total | 64 | 145 |
METAL CASTING SCIENCE AND ENGINEERING DIPLOMA COURSE IN MECHANICAL ENGINEERING SIXTH SEMESTER MODEL QUESTION PAPER
DERARTMENT OF TECHNICAL EDUCATION DIPLOMA COURSE IN MECHANICAL ENGINEERING SIXTH SEMESTER MODEL QUESTION PAPER METAL CASTING SCIENCE AND ENGINEERING Time: 3Hrs Max marks: 100 Note: 1.Section-1 is compulsory 2. Answer any two full questions from each of the remaining sections Section- 1 1. (A) Fill in the blanks with appropriate words: 5X1=5 (¡) The casting is one of the basic ______________ process. (ii) Reducing variability and defects is the essence of _____________concept. (iii) The ultrasonic waves are usually generated by ______________effect. (iv) The crucibles used in foundries are made of clay and ______________materials. (v) The risers promote _______________solidification (B) Write an explanatory note on Internet Based Foundry Engineering 5 |
POWER PLANT ENGINEERING MODEL QUESTION PAPER DIPLOMA COURSE IN MECHANICAL ENGINEERING SIXTH SEMESTER
DERARTMENT OF TECHNICAL EDUCATION DIPLOMA COURSE IN MECHANICAL ENGINEERING SIXTH SEMESTER MODEL QUESTION PAPER POWER PLANT ENGINEERING Time: 3Hrs Max marks: 100 Note: 1.Part-I is compulsory 2. Answer any six full questions from Part-II, Part-III, and Part-IV Choosing at least two from each section PART- I 1 A) Fill in the blanks with appropriate words:- 1X5 I) The fuel used in thermal power plant is ______________. ii) The moderator are used in nuclear reactor to control the_____________ neutrons iii) ______________ standby plants to hydro and steam power plant iv) The nuclear power plant is not suitable for ______________.load condition v) In steam power plant the generation power is _______________ B) Write a note on Indian energy scenario. 5 |
REFRIGERATION AND AIRCONDITIONING DIPLOMA IN MECHANICAL ENGINEERING 6TH SEM
Courtly:dte board
DEPARTMENT OF TECHNICAL EDUCATION
DIPLOMA COURSE IN MECHANICAL ENGINEERING
SIXTH SEMESTER
MODEL
QUESTION PAPER
REFRIGERATION AND AIRCONDITIONING
Time: 3Hrs Max
marks: 100
Note:
1.Part-I is compulsory
2. Answer any six full questions
from Part-II, Part-III, and Part-IV
Choosing at least two from each section
PART- I
1 A) Fill
in the blanks with appropriate words:-
1X5
I)
The refrigerant used in dairy refrigeration is ______________.
ii)
The air refrigerator working on
_____________cycle
iii)
______________ unit of refrigeration
iv)
The automatic expansion valve is used to control the
______________refrigerant.
v)
The motor and compressor mounted on the same casing
in_______________compressor
B) Write a note steam jet
refrigeration 5
PART-II
2
a) Define the following terms w.r.t refrigeration
i) Refrigerating effect ii)
C.O.P 4
b) Explain with block diagram Carnot
refrigeration Cycle. 5
c) State the advantage and disadvantages of
air refrigeration system.
6
3 a) Explain with flow
diagram of working of Vapour compression
cycle . 8
b) A Refrigeration
working on Bell-Coleman cycle operates between pressures
limits of 1 bar and 8.5 bar. Air is drawn from the cold chamber at 100C and
it is cooled to 300C before entering the expansion follow the law PV ^ 1.35 = C
7
Determine theoretical COP of the system
4
a) Explain with the help of TS and HS diagrams the working of
vapour compression 5
Refrigeration system.
b) Explain the effects of
super heating and under cooling. 5
c) Differentiate between vapour absorption and vapour
compression refrigeration system 5
PART-III
5 a) State the Advantages
of air cooled and water cooled condensers 4
b) Sketch and explain hermitically sealed compressor 6
c) Differentiate
between natural and forced cooling system
5
6 a) Describe forced
convection types
Evaporators .
4
b) State the properties
of good refrigerants.
6
c) Sketch and explain thermostatic
expansion valve 5
7 a)
Explain the working of high side float
valve 5
b) State the function of solenoid
valve. 5
c) Describe briefly dairy refrigeration 5
PART-IV
8
a) Explain with schematic diagram water
cooler 5
b) Explain Psychometric chart & its use 5
c) Describe briefly psychometric process
a) Sensible heating b) Adiabatic
saturation
5
9 a) Explain installation procedure of
refrigeration systems . 5
b) State the factors affecting Air conditioning
5
c) Describe briefly window air conditioner 5
10 Write short note on any three of the following 5x3=15
i) Tools used in refrigeration and Air
conditioner installation r
ii) Packaged air
conditioner
iii) Cold storage
iv) Evaporator pressure regulator
v) Air refrigeration
system
Popular Posts
-
Search Tags: 3 rd sem mechanical engineering syllabus, mech engg syllabus 3 rd sem, mechanical engg syllabus 3rd sem, dte syllabus, dte.k...
-
Search labels: diploma mechanical engineering 5 th sem syllabus, diploma mech engg5 th sem syllabus, diploma in mechanical engineering 5...
-
Search tags: 4 th sem diploma mechanical engineering syllabus, fourth sem syllabus with subject codes, dte board 4 th sem syllabus, 2nd...
-
Polytechnic civil engineering syllabus 3rd semester DIPLOMA CIVIL ENGINEERING Karnataka 3 rd SEM SYLLABUS ITH SUBJECT CODES, syllabus of ...
-
Syllabus for diploma in civil engineering 5th sem, Diploma Civil engg 5 TH semester syllabus subjects name and Subject codes DTE...
-
DIPLOMA MECHANICAL ENGINEERING SYLLABUS 1ST SEM, diploma engineering syllabus for mechanical engineering, First semester mechanical engin...
-
DIPLOMA IN CIVIL ENGINEERING 6TH SEM SYLLABUS With Subject codes and Subject names, Examination scheme, Minimum marks GOVERNMENT OF KARNA...
-
Syllabus for Diploma in Mechanical engineering 2nd SECOND SEMESTER Syllabus (GENERAL) PDF Copy Diploma MECH ENGG ENGINEERING DIPLOMA DTE/BTE...
-
4TH SEM DIPLOMA CIVIL ENGINEERING SYLLABUS, engineer, engineering syllabus For latest Syllabus PDF: https://www.engineeringdte.com/p/diplo...
-
Search labels:-Diploma mechanical engineer,engineers 6 th sem syllabus, Diploma mech 6 th sem syllabus, dte syllabus, dte.kar.nic.in ...